Sider-Deck

Sider-Deck is a cement-based / polymer-modified deck coating designed for resurfacing and decorating new or existing concrete pool decks, concrete floors, existing pool deck coating or pebble/rock decking surfaces.  It is cool, durable, smooth and protects your deck; and at the same time decorative!  Sider-Deck is packaged as a kit and available in different pre-mixed colors as well as many different textures; and ready to accept Sider-Deck Sealer. 

Sider-Deck Sealer is the ultimate Silicone/Acrylic-Based Concrete & Masonry Deck Sealer.  Sider-Deck Sealer is available integrally colored with high quality pigments, which provides an integral skid-resistant protective and decorative sealer over concrete and masonry decks and specially formulated for application over Sider-Deck.  It promotes color uniformity of Sider-Deck and concrete surfaces, colors architectural details and graphics, and may be used to recoat existing Sider-Deck Sealer.

  MATERIALS:

Sider-Deck is available as a 53-lb (24 kg) ready-to-use kit, comprised of:

       Part A - a 42 lb. (19 kg.) bag of powder

        Part B - a 1.3 gal. (5 liters) container of liquid

Sider-Deck Sealer is available in a 5-gallon pail or 1-gallon container:

Sider-Deck Sealer is composed of a durable silicone/acrylic blend.  It is formulated for many applications over concrete and Sider-Deck.  Such applications include pool decks, concrete driveways & garage floors (solvent-based only), patios and walkways, etc…  Sider-Deck Sealer is available in integral colors and skid resistant.

  SURFACE PREPARATION:

Ø Sider-Deck

Surfaces must be free of all bond-inhibiting materials, including dirt, efflorescence, release agents, grease and oils, and other foreign particles.  Remove paint, loose or damaged materials by water blasting, sandblasting or mechanical wire brushing.  Surfaces should be pressure-washed to ensure the removal of all dirt, mildew, algae, etc… You may recoat an existing cement-based, unpainted & unsealed pool-deck coating or a pebble/rock (concrete-based) decking surface with Sider-Deck.  If applying directly over concrete, the concrete should be cured for at least 5 days and a broom-finish surface is recommended for a proper bond.  For existing smooth surfaces, an acid wash/acid-etch on the existing surface is recommended along with a neutralizing treatment (example, TSP) to expose the aggregate and provide a proper mechanical bond. 

Damages and indentions should be repaired and leveled with Sider-Repair or Sider-Screed.    Tape all areas that are not to be coated, or you may trim them with a brush.  To prevent the product from falling into the pool, lay a thin plastic tarp on the water and tape around the edges.  Ensure that the substrate has been well dampened and allowed to slightly dry; to be humid but not wet to the touch.

• Expansion Joints:

      Plastic expansion joints:  Tape the joints with a moisture resistant, non-paper tape (ex: electrical tape).  Follow the installation instructions for Sider-Deck.  Allow Sider-Deck to dry for approximately 4 to 6 hours; do not allow it to dry too long, as it will be difficult to remove the tape.  Remove the tape, then with a putty knife and a damp sponge, smooth any jagged edges and clean the joints.

Saw-cut expansion joints:  Follow the installation instructions for Sider-Deck.  Allow Sider-Deck to dry; then with a putty knife, edge-trowel or pointed-trowel, clean the joints.  You may also use an electric grinder with a masonry blade to re-cut the joints, if Sider-Deck is too hard to remove with hand tools alone.  

            Ø Sider-Deck Sealer:

       For Sealer applications, Sider-Deck is ready to accept Sider-Deck Sealer after 24 to 48 hours of drying time (for application during cold weather, longer drying time may be required and allow additional drying time if it has rained on Sider-Deck prior to the application of Sider-Deck Sealer).  Apply outside or in a well-ventilated area. 

  MIXING INSTRUCTIONS:

ENSURE THAT THE MATERIAL IS STORED IN A COOL DRY PLACE IN THE  SHADE.  IF WARM MATERIAL IS MIXED, IT WILL SET RAPIDLY.  

SIDER-DECK:

Shake well and pour the Sider-Deck liquid into a clean bucket and then add ½ bag of Sider-Deck Powder.  Mix thoroughly with a drill and mixing paddle for 10 to 20 seconds. Then add the rest of the powder and mix for no less than 3 - 5 minutes to yield a good plasticity and achieve a homogeneous mix. For darker colors, a longer mixing time may be required to ensure proper color dispersion.  Always pour the liquid component in first and then add the powder while mixing for optimal results.  Clean around the inside top edge of the mixing bucket to ensure total blend of the material.  

Do not add any products in the mix.  However, you may add a minimal amount (½ cup to 1 cup) of clean potable water to achieve a desired workability.  If adding water to the mix, ensure that the water is cool and not directly from the hose laid in the sun.  Do not water-down the material too much as it will prevent the application of a nice thick coat.  If the material becomes too thick to apply during the application process, you may add a small amount of water in the mix and remix the material to achieve the desired consistency.  Do not use partially set or frozen material in the mix.

SIDER-DECK SEALER:

Stir to a uniform consistency by hand in the container or with a drill and paddle mixer directly in the pail.  Avoid creating foam or air bubbles.  If using more than one container, mix the containers together for color uniformity.

  INSTALLATION:

IT IS RECOMMENDED TO APPLY THE MATERIAL EARLIER IN THE MORNING DURING COOLER TEMPERATURES, AS A HOT CONCRETE SURFACES  MAY FORCE THE MATERIAL TO SET TOO QUICKLY.

SIDER-DECK

Base-Coat/Skim Coat:

Note: The 'Base-Coat/Skim-Coat' is not required, it is designed for application over rough concrete in need of resurfacing prior to the application of the 'Texture-Coat.'   The 'Texture-Coat' may be applied directly over the concrete surface.

   Roller Application

Apply a first coat of Sider-Deck on a humid and cool, but not wet concrete.  Apply with a paint roller and roll in all directions, dipping your roller directly in the mixing pail (do not use a roller pan).  Then, with another clean paint roller, immediately lightly roll over Sider-Deck in one direction to create a smooth and even texture.  You may have to clean the roller occasionally to avoid build-up.  Do not roll over applied material that has already started to set, as it will damage it.  Apply Sider-Deck to a maximum thickness of 1/8”.

    Trowel Application

Apply a first coat of Sider-Deck with a stainless steel trowel and trowel it smooth.  Do not over-trowel or trowel over a partially set material as it will create ‘burn marks'. Apply Sider-Deck to a maximum thickness of 1/8”. 

Texture-Coat:

Note: The 'Texture-Coat' may be applied directly over the concrete surface if the deck is in good condition without the need of the 'base-coat/skim coat.'

   Knock-Down

You may apply Sider-Deck in the knock-down texture directly over the concrete without the need of a base-coat/skim coat. A base-coat/skim coat may be used over concrete surfaces in need of re-surfacing. If a skim coat is applied, allow it to dry for a minimum of 24 to 48 hours but a maximum of three days (for application during cold weather, longer drying time may be required) prior to the application of the knock-down texture.  A knock-down texture is always required to ensure maximum slip-resistance.

With a hand-held spray hopper gun (at approximately 25 – 35 PSI) or our Deck-Sprayer (mechanical sprayer-call for details), spray Sider-Deck.  Hold the hopper-gun or Deck-Sprayer at the same distance and move with a steady, even stroke creating the desired pattern.  Once sprayed, lightly run a clean stainless steel trowel over the texture to create the knockdown texture.  Do not allow the spray pattern to dry excessively, as you will not be able to run your trowel to create your knockdown pattern.  The knock-down texture will create a 70 % - 80% coverage over the concrete.  The Sider-Deck Sealer will provide the final and complete color finish.

Sider-Deck Sealer

Apply outside or in a well-ventilated area.  Sider-Deck is ready to accept Sider-Deck Sealer after 24 to 48 hours of drying time but a maximum of three days (for application during cold weather, longer drying time may be required & allow additional drying time if it has rained on Sider-Deck prior to the application of Sider-Deck Sealer). 

Roll-on the first coat, continuing in the same direction until entire surface is coated (3/8” nap soft-woven roller sleeve is recommended for optimum uniform appearance).   Dip the roller directly into the pail; do not use a roller pan.  Allow the first coat to dry for at least 2-4 hours, then roll-on the second coat, continuing in the same direction until the entire surface is coated.  

Apply each coat in a thin layer to prevent the development of air bubbles. Apply light pressure while rolling Sider-Deck Sealer to prevent roller marks. It is recommended to apply the second coat perpendicular to the first coat (cross-coat) to ensure proper matrix coverage and protection.

Texture Examples:

           Fine Knock-Down                       Medium Knock-Down

Designed Examples: (two coats/colors with stencils/tape)

     Knock-Down Tile Pattern                           Small Tile Pattern                          Large Tile Pattern

  LIMITATIONS:

Sider-Deck:

Ambient and surface temperatures must be 41° F (5° C) or above during application and drying time.  Supplemental heat and protection from precipitation must be provided as needed.  Do not apply to overheated, excessively dry or frozen substrate nor during periods of high winds.  Apply Sider-Deck to a maximum thickness of 1/8”.  Use only on surfaces that are sound, clean, dry, and free from any residue, which may affect the ability of the Sider-Deck to bond to the surface. A knock-down texture is always required to ensure maximum slip-resistance; this system is not presented as a slip-proof product and Sider-Oxydro, Inc. will not be held liable for accidents.

Sider-Deck Sealer:

Ambient and surface temperatures must be 41° F (5° C) or above during application and drying time.  Supplemental heat and protection from precipitation must be provided as needed.  Use only on surfaces that are sound, clean, dry, and free from any residue, which may affect the ability of the Sider-Deck Sealer to bond to the surface. Once your deck has been coated, ensure that it will not be exposed to rain or freezing temperatures for at least 24 hours to allow for a proper drying period. 

It is necessary for Sider-Deck Sealer to dry at least 24 hours to allow light foot traffic.  The owner should only allow light use of the deck for 48 hours.  Placing of patio furniture, hard-soled shoes and heavy use of the deck should be avoided for at least one week.  For applications over driveways and garages, allow one to two weeks (depending on ambient conditions and temperatures) prior to driving over Sider-Deck/Sider-Deck Sealer.

Note:  Due to the natural ingredients which make-up Sider-Deck or the nature of the substrate, the development of efflorescence may naturally occur and appear on the surface.  Final texture and color of installed material may vary due to its composition and variations in application tools and techniques, weather and lighting conditions, and other factors beyond the control of the manufacturer.  Sider-Oxydro, Inc. assumes no liability for variations caused by conditions beyond its control.

  MAINTENANCE:

Sider-Deck and Sider-Deck Sealer are high-quality durable products that will give you years of enjoyment and beauty.  Sider-Deck and Sider-Deck Sealer are relatively low-maintenance products.  To clean Sider-Deck and Sider-Deck Sealer on a regular basis, hose it off with clean fresh water.  For a deeper cleaning, please call for details.

  COVERAGE:  

Sider-Deck:

v     One Coat Rolled-on (skim coat) + Knock-Down Texture:  90 square feet per 53 lb. (24 kg) Kit.

v     Knock-Down Texture directly over concrete:  150 - 200 square feet per 53 lb. (24 kg) Kit.

(Divide your total square foot area by  ~90 or ~150 to determine the approximate amount of kits needed.)

Sider-Deck Sealer:

v      80 sq. ft. in two coats / 1 gallon container

v        400 sq. ft. in two coats / 5 gallon pail

Coverage is approximated and is given for estimating purposes only.  Actual jobsite coverage may vary according to substrate conditions and application techniques.

   STANDARD COLORS

  RECOMMENDED TOOLS:

     Drill:            1/2 in. drill, Type 3, 7.8 A / 450 rpm  ~DeWalt or similar

    Paddle:        Large square mortar paddle (not small blue paint paddle)

  Pail:             5-gallon pail or more

  Roller:          9" shed-resistant fabric roller, 3/8" to 3/4" nap.

    Trowel:         Standard stainless steel trowel

    Spray Hopper:  A standard pneumatic texture spray hopper gun (right photo)

  Deck-Sprayer:  Mechanical sprayer for a knock-down finish (above photo - call for details)

The use of more complex equipments (ex: stencils and templates, etc...) is possible.  For more detailed instructions, please contact us.

  STORAGE & SHELF LIFE:

Shelter in a dry environment from extreme heat, direct sunlight, rain and freezing.  Shelf life is 6 months in the original sealed packaging properly sheltered in a dry environment.

  TECHNICAL ASSISTANCE:

For technical inquiries, contact Sider-Oxydro, Inc. at Toll Free: 888-743-3750 or click below for our complete contact information.

  CLEAN UP:

Sider-Deck:

Clean tools and equipment with water after use prior to drying. Clean up and remove all debris and materials from the site caused by the installation according to federal, state and local regulations and dispose of waste. 

Sider-Deck Sealer:

Clean spills and spatters and tools immediately with Xylene or Toluene (oil-based). Follow manufacturer's safety recommendations when using any solvent. Use “waterless” hand cleaner to remove dried material from skin.

And now, enjoy using SIDER-DECK / SIDER-DECK SEALER and benefit from this revolutionary technology developed by Sider-Oxydro, Inc., innovative leaders in the construction industry since 1937.

Text and images used in this website are provided for information purposes only. THIS IS NOT A SPECIFICATION! While every effort has been made to be comprehensive and accurate, the publisher cannot accept any liability for omissions or errors. Users should contact Sider-Oxydro, Inc. for the product(s) referred  to in this website to ensure that any information used to make decisions about the product(s) is as up-to-date and complete as possible.

Text and images contained in this website and its links are considered property of Sider-Oxydro, Inc. and may not used or reproduced without the express written consent of Sider-Oxydro, Inc. and as well without the reference name:' Sider-Oxydro, Inc'.